Choose by the job, not by the product. Wet screeding levels fresh concrete in the same pour, so it suits new slabs where cost and speed matter most. Dry screeding, a self levelling topping laid over a cured slab, suits existing floors and commercial jobs where flatness tolerance matters more than price. If the slab
Wet Screed vs Dry Screed – Which Is Better for Your Project? Read More »
Most anhydrite screed problems come back to three causes: moisture left in the screed, laitance left on the surface, and a screed laid too thin or on a badly prepared base. Get those three right and most of the cracking, debonding, hollow spots and covering failures described below never happen. The rest of this article
Anhydrite Screed Problems – Things to Consider Read More »
Screed is ready to cover when it tests dry, not when the calendar says so. As a planning rule, allow 1 day of drying per millimetre of thickness for a traditional sand and cement screed at around 20 degrees C with good ventilation, so a 50 mm screed plans at about 50 days before testing.
How to Dry Screed Quickly: A Comprehensive Guide Read More »
Anhydrite screed, also called calcium sulphate screed, is a pumpable, self levelling floor screed that suits underfloor heating well because it flows around pipes and conducts heat efficiently. Its two non negotiable rules are moisture and laitance: the screed must be dry enough, tested properly, before it is covered, and the weak laitance skin on
Depth and finish decide this choice. Cement screed builds a new floor base, typically 25 mm to 40 mm thick, and takes weeks to dry before it can be covered. Microcement is a decorative finish in its own right, laid only a few millimetres thick over a sound existing surface, and ready far sooner. If
Cement Screed vs Microcement – Which Is Better for Flooring? Read More »
Screed and mortar are not interchangeable, even though both are cement based. Screed is a levelling layer laid horizontally over a floor slab to give a flat surface for a floor covering. Mortar is a bonding paste laid between bricks, blocks or stones to hold masonry together and carry load. If the job is a
What’s the Difference Between Screed and Mortar? Read More »
Floor screed is the levelling layer laid over a structural concrete slab to give a flat, level surface for a floor covering. It is not the structural floor, and it is not a wearing surface on its own. Its thickness, its bond to what lies beneath, and its drying time decide whether the finished floor
What is Floor Screed? It’s Types, & Factors to Consider 2026 Read More »
Depth decides this choice more than anything else. If you need to level a few millimetres, feather out dips, or get a floor covered the next day, self levelling compound is the right tool. If you need to build up 25 mm or more, form a fall or a ramp, carry a heated floor, or
Screed vs Levelling Compound – Which Should You Use? Read More »
The right primer for self levelling compound is decided by the substrate, not by the brand on the tin. Porous concrete usually takes an acrylic primer, often in two coats, because the first coat soaks in and the second builds the film the leveller bonds to. Smooth, power floated concrete, calcium sulphate screed and timber
Best Primer for Self Leveling Compound in 2026 Read More »
Screed cracks for a reason, and the reason decides the repair. Shrinkage cracks come from water leaving the screed. Thermal cracks come from heating too early or too fast. Structural cracks come from movement below, a debonded section, or a screed laid too thin for its construction. Sealing a crack without removing its cause only
Screed Cracking – Causes and Prevention 2026 Read More »
Screed is the thin levelling layer laid over a structural concrete slab to give a flat, level surface for a floor covering. It is not the structural floor and it is not a wearing surface on its own. It carries the floor finish, it can hide services and insulation in a floating construction, and its
What is Screed? The Ultimate Guide (2026) Read More »
Most cracks in underfloor heating screed come from one of four things: the heating was switched on too early or turned up too fast, movement joints are missing where the floor changes, the screed is thinner than the heated construction needs, or the screed dried too fast in its first days. A fine surface crack
Underfloor Heating Screed Cracking – 2026 Read More »
You’ve spotted moisture on your walls. Now you need to know what type of damp you’re dealing with, because the wrong fix wastes money and doesn’t solve the problem. This guide shows you exactly how to identify rising damp versus penetrating damp, what causes each type, and what actually works to fix them. What’s the
Rising Damp vs Penetrating Damp: How to Tell the Difference and Fix It Read More »
What is Screed? Screed is a material used to provide a smooth, level surface before laying floor finishes such as tile, vinyl, or carpet. It is applied over concrete or wood subfloors to fill in any uneven areas, creating a flat base. There are two main types of screed, traditional screed and liquid screed. Traditional
Liquid Screed vs Traditional Screed – 2026 Read More »
Damp proof membranes (DPMs) stop moisture from travelling through floors, walls, and foundations. Choosing the right type matters because the wrong membrane leads to damp problems, wasted money, and failed projects. This guide compares every major DPM type so you can pick the one that actually works for your situation. What Is a Damp Proof
Damp Proof Membrane Types Comparison: Which One Actually Works for Your Project? Read More »
